Difference between revisions of "ESP32 TFT LCD with Camera(3.5'')"

Revision as of 02:06, 6 June 2022

Introduction

The 3.5" 320x480 TFT LCD driver is ILI9488, it uses SPI for communication with ESP32, the SPI main clock could be up to 60M~80M, make the display smooth enough for videos; and the camera OV2640 with pixel 2M, with this camera, you can make applications such as remote photography, face recognition…. While the camera not used, you can freely use all these pins with the breakout connectors, to connect the ESP32 display with sensors/ actuators, suitable for IoT applications.

Model: Resistive: ESPTFT35RE
Model: Capacitive: ESPTFT35CA

Features

• Integrated ESP32 Wrover 2.4G WiFi and Bluetooth
  
• Wi-Fi Protocols: 802.11b/g/n(802.11n up to 150Mbps),A-MPDU and A-MSDU aggregation and 0.4us guard interval support
  
• Wi-Fi Frequency range: 2.402GHz - 2.483Ghz
  
• Bluetooth Protocols: Bluetooth v4.2 BR/EDR and BLE specification
  
• Bluetooth Radio: NZIF receiver with-97 dBm sensitivity, Class-1/class-2 and class-3 transmitter, AFH
  
• Bluetooth Audio: CVSD and SBC
  
• Arduino Compatible: You can play it with Arduino IDE
  
• OV2640: A 1/4inch CMOS UXGA (1632*1232) image sensor manufactured by OmniVision
  
• OV2640 supports output images up to 2 million pixels
  
• LCD 3.5 inch Amorphous-TFT-LCD (Thin Film Transistor Liquid Crystal Display) for mobile-phone or handy electrical equipment
  
• LCD Driver: ILI9488
  
• LCD Resolution: 320*480
  
• NS2009: A 4-wire resistive touch screen control circuit with I2C interface, which contains A 12-bit resolution A/D converter
  
• FT6236 Series ICs are single-chip capacitive touch panel controller IC with a built-in 16 bit enhanced Micro-controller unit (MCU)
  
• Power supply: 5V, Type-C USB
  
• Micro SD card slot on the board
  
• Board size: 66mm * 85mm
  

Diagram

Pin Assignment

Note:IO34/IO35/IO36/IO39 input only.
Dimension

Note:unit is mm.

Usage

Warning: Don't operate when in power supply on
Github:Project_Touch_Screen_Camera

Software setup

NOTE: In order for the project to work normally, please install the same version.
1.Install the Arduino IDE V1.8.10.
2.Install the ESP32 boards supporting V1.0.4

• After Arduino IDE installed, there is no package to support ESP32, we need to install the ESP32 package in Arduino IDE to continue.
  
• Select “File>Preferences>settings>Additional Boards Manager URLs” to fill the link: https://dl.espressif.com/dl/package_esp32_index.json
  

• Click “Tools>Board>Boards Manager” to search for and install the ESP32 library:
   

3.Install Adafruit GFX library V1.10.4

Click “Tools> Manager Libraries” to search for and install Adafruit GFX library.

4.Install LovyanGFX library V0.3.4

Click “Tools> Manager Libraries” to search for and install LovyanGFX library.

5.Select and setting the parameter in the Tools menu, as the picture:

Draw on LCD

1. You can get the code from here: Core
2. Open the file “\Project_Touch-Screen-Camera-master\touch_draw_v2\touch_draw_v2.ino”. Select the screen type used and comment out the ones that are not used.

#include <Wire.h>
#include "SPI.h"
#include <LovyanGFX.hpp>
#include "makerfabs_pin.h"

//Choice your touch IC
#define NS2009_TOUCH    //Resistive screen driver
//#define FT6236_TOUCH  //Capacitive screen driver

3. Verify it and upload.

If failed to upload the code as the picture, please upload again and try to press the Flash switch when the code is uploading.

4. After done uploading, repower the ESP32 and you will get the drawing board.

Display the picture

1. You can get the code from here:Core
2. Copy the picture you want to show to the SD card. Insert the SD card into the board.
3. Open the file “\Project_Touch-Screen-Camera-master\SD2TFT\SD2TFT.ino”. The name of the showed picture must be filled in the string array, such as the below code.

String img_file[5] =
    {
        "/1.bmp",                
        "/2.bmp",
        "/3.bmp",
        "/4.bmp",
        "/5.bmp"};

4. Verify and upload the code, you will get a digital photo frame.

Camera

1. You can get the code from here: Core
2. Open the file “\Project_Touch-Screen-Camera-master\Camera_v2\Camera_v2.ino”. Choose the screen type and modify the code.<be>

//#define NS2009_TOUCH  //Resistive screen driver
#define FT6236_TOUCH //Capacitive screen driver

#ifdef NS2009_TOUCH
#include "NS2009.h"
const int i2c_touch_addr = NS2009_ADDR;
#define get_pos ns2009_pos
#endif

#ifdef FT6236_TOUCH
#include "FT6236.h"
const int i2c_touch_addr = TOUCH_I2C_ADD;
#define get_pos ft6236_pos
#endif

3. Verify and upload the code, you will get a camera.

Indoor Environment Expansion board

This is an expansion board for measuring CO2, TVOC, Temperature, and Humidity. The board is design for ESP32 TFT LCD with Camera(3.5')(also for 3.2' one). For using, plug the board into the ESP32 TFT LCD board directly, program the ESP32. The ESP32 TFT LCD will turn to a meter for monitoring the environment.
Model: Indoor Environment Expansion

Features

• SGP30 Air Quality Sensor, measuring TVOC and CO2.
• DHT11 temperature and humidity sensor.
• Active buzzer.

Hardware

• Schematic
  

Using

• Plug the expansion board into the ESP32 TFT LCD board.
• Loading the program obtained from GitHub.
• Reset the ESP32, and wait a minute.
• The LCD will display the measure of CO2, Temperature, Humidity.
• When the CO2 level is high over 1000, the buzzer on board rings.

Display CO2 historical level

• Plug the expansion board into the ESP32 TFT LCD board.
• Loading the program.
• Reset the ESP32 board, the ESP32 will start to record the CO2 level and TVOC level, and draw the historical values to line.

FAQ

You can list your question here or contact support@makerfabs.com for technology support. Detailed descriptions of your question will be helped to solve your question.

• Q1: Why the display fails to respond sometimes I touch.
  

A1: The touching interface is loose, please reconnect it.

• Q2:Can't upload the code
  

A2:Let ESP32 in download mode by pressing the RESET key after hold the FLASH key when you're uploading the code.

Resources

• ESP32 wrover datasheet
• Github: Project_Touch-Screen-Camera
• Github: Project-ESP32-LVGL
• Schematic