Difference between revisions of "Maduino Zero LoRaWAN Node"

From MakerFabsWiki
Jump to: navigation, search
Line 22: Line 22:
*Power by USB or battery
*Power by USB or battery
*Support Micro SD Card
*Support Micro SD Card
*Default Baudrate 115200bps
*Operating temperature:-40℃ ~ 85℃
*Operating temperature:-40℃ ~ 85℃

Revision as of 05:41, 18 August 2021

About the product


LoRa (short term for long range) is a spread spectrum modulation technique derived from chirp spread spectrum (CSS) technology. LoRaWAN is the network system architecture and communication protocol specification for LoRa, developed by the LoRa Alliance. LoRaWAN is a Media Access Control (MAC) layer protocol that enables LoRa in wider applications. The LoRa Alliance defines the networking layer and the system architecture for the network.

Maduino Zero LoRaWan is a solution based on ATSAMD21G18 MCU and LoRaWAN module Ra-07H. The LoRaWAN module Ra-07H is based on the ASR6501 chip, it integrated the LoRa radio transceiver, LoRa modem, and 32-bit RISC MCU, to support LoRa modulation mode and (G) FSK modulation mode. Maduino LoRaWan acts as a LoRaWAN node to transmit/receive the local data to the network by connecting LoRaWAN Gateway. With this module, users are easy to prototype LoRaWAN projects easily in few hours.

Maduino LoRaWan is compatible with Arduino and basic demos communicating with TTN are provided. Note that for LoRaWAN communication, a LoRaWAN router is needed.

Model: Maduino Zero LoRaWAN Node
Maduino Zero LoRaWAN Node 101.jpg


  • ATSAMD21G18, 32-Bit ARM Cortex M0+
  • Interface: I2C /18*GPIO
  • Arduino Compatible.
  • Support LoRaWAN protocol.
  • Operate frequency:803MHz~930MHz
  • Minimum receiving sensitivity:-137dBm
  • Max Transmit power: +21dBm
  • Power by USB or battery
  • Support Micro SD Card
  • Default Baudrate 115200bps
  • Operating temperature:-40℃ ~ 85℃

Preparation before using


  • !!!Note The LoRaWAN node does not transmit the data to TTN by LoRaWAN without the LoRaWAN gateway router which has been set as TTN gateway.
1. The LoRaWAN gateway router used in the demo is a Dragino LIG16 one.
2. Configure the router as a TTN Gateway follow the user manual of the LIG16 Gateway #Recources.
3. Configure the frequency you need.
  • Please plug the LoRa antenna into the board.


  • Install Arduino IDE for programming.

Transmit data to TTN

  • Overview
1.This demo uses Maduino Zero LoRaWAN node to collect the DHT11 module reading and transmit these reading to TTN with the LoRaWAN.
Maduino Zero LoRaWAN Node 103.jpg
  • TTN Application
1.The Things Network(TTN) is a global community building an open-source and decentralized LoRaWAN network.
2.For transmitting the data to TTN(The Things Network), It is necessary to learn the using of TTN in advance, such as how to set an application, etc. After setting your application of TTN, there are three parameters to be important: Device EUI, APP Key, APP EUI.
3. Enter the TTN website: https://console.thethingsnetwork.org/, and log in your account.
4. Go to the console, select a cluster to start adding devices. (I choose the EU)
5. Select Application on the page and add a new application.
6. Fill in the application ID and other information, then create it.
Maduino Zero LoRaWAN Node 107.jpg
7. Add an End device, select the manually to choose the active mode to OTAA and LoRaWAN version, then follow the reminders to type in the parameters.
Maduino Zero LoRaWAN Node 108.jpg
Maduino Zero LoRaWAN Node 109.jpg
Maduino Zero LoRaWAN Node 110.jpg
Maduino Zero LoRaWAN Node 111.jpg
8. In the Device of the Application, three parameters will be seen that had to put into the code.
Maduino Zero LoRaWAN Node 112.jpg
9. On the device page, it is necessary to set the payload formatters for decode the payload LoRaWAN node transmitted. Choose the Uplink and select the Javascript. Type in the following code and save.
function Decoder(b, port) { 
  var var1 = b[0];
  var var2 = (b[1] << 8) | b[2];

  return {
    field1: var1,
    field2: var2/10
Maduino Zero LoRaWAN Node 113.jpg
10. The TTN application setting is finished.
  • LoRaWAN Gateway
1. Configure the LoRaWAN router to TTN gateway, and set the operating frequency of LoRa.
2. Power it and put it aside.
Maduino Zero LoRaWAN Node 115.jpg
  • Maduino Zero LoRaWAN Node
1.Follow the below list to connect the DHT11 module to Maduino Zero LoRaWAN Node.
LoRaWAN Node DHT11
Maduino Zero LoRaWAN Node 106.jpg
2.Open the code obtained from Github with Arduino IDE.
3.Select the development board("Arduino Zero") and port.
4.Replace the three parameters(Device EUI, APP Key, APP EUI) to yours in the code.
Maduino Zero LoRaWAN Node 104.jpg
5.Verify and loading it.
6.Tips: Below some AT commands used in the code.
AT+CJOINMODE=0     "0" means to set the JOIN mode (the way of connecting the LoRaWAN)to OTAA.
AT+CJOIN=1,0,10,1  First "1" means to enable the JOIN, "0" means to turn off the auto-connect, "10" means the circle is 10S, "1" means sending one time.
AT+DTRX=1,2,5,XXXXX  "XXXX" is the string transmitted.
7.Note: When the LoRaWAN module work in OTAA mode, the operation frequency will be automatically set to the same frequency as the matching router, if your router frequency is 868Mhz, the module will work in 868Mhz that the LoRaWAN module support.
  • Result
1.Wait for a minute, you can view something received in TTN.
Maduino Zero LoRaWAN Node 105.jpg
2.As the picture, the original payload is 3C0119, the date after format decoded is 60 and 28.1, which means the temperature is 28.1 ℃ and humidity is 60%.


You can list your question here or contact support@makerfabs.com for technology support. Detailed descriptions of your question will be helped to solve your question.